Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Burbank, CA
Gate access control work in Burbank runs into two realities faster than almost anywhere else in the Valley: hundred-degree summers that cook limit switches, and a stock of 1940s and 1950s homes whose original gate posts have moved enough to throw off photo-eye alignment by inches. Most Burbank calls we take start with a keypad that stopped reading codes or a gate that reverses for no reason, and the fix usually lands between $450 and $850. Call Vance Gate Repair at (213) 463-6296 and we’ll put the price in writing before anyone touches a tool.
Why Burbank Homes Are Different
Burbank’s Rancho Equestrian District keeps urban horse properties alive in Los Angeles County, and that means gates built for a different job: 16 to 20 foot clearances for horse trailers, dual-swing configurations that weigh more than anything on a standard Burbank lot. We service those gates alongside the post-WWII tract homes in Magnolia Park and the Hillside District, where original wrought-iron swing gates still hang on mortared concrete pillars that have shifted over 70 years. A gate that scrapes the driveway today was usually hung plumb in 1952 and has simply outlasted its footing. Summer thermal cycling expands steel frames and tracks enough to crack older welds; fall Santa Ana winds, which hit the Burbank flatlands hard, blow unbalanced gates off their hinges or strip the gears on automatic operators. October and November are our busiest emergency months in Burbank for exactly that reason. Burbank’s building and safety department also enforces its own permit review for automated gate installations, separate from LA County, and inspectors flag UL 325 photo-eye placement on commercial properties along Alameda Ave. Homeowners who skip the permit on a motor swap near the studio corridors get cited.
Our Main Burbank Services
Most Burbank homeowners call us for one of three jobs: a broken gate, a new gate, or an operator that stopped listening. Here is how each one works here.
Gate Repair in Burbank
Repair work in Burbank usually means hinge failure on an original iron gate or a track issue on a slide gate that has been fighting the Valley heat for decades. We rebuild the swing geometry first, then address the operator, because a gate that closes crooked will destroy a new motor within a year. Same-day service is available for emergency jobs, especially during Santa Ana season. Full details are on Gate Repair in Burbank.
Gate Installation in Burbank
New gate work in Burbank has to account for the old post problem: many driveways still have their original masonry pillars, and we either re-plumb the posts or set new steel ones before the gate is hung. Rancho-area clients often need the extra-wide dual-swing configuration for trailer access. Installation is scheduled, not dispatched same-day. See Gate Installation in Burbank for what is involved.
Gate Motor & Opener in Burbank
Burbank operators fail most often from thermal stress: capacitors and limit switches wear out faster when the gate runs through a 105-degree afternoon. We service all nine major automation brands rather than steering you toward a replacement motor unless the existing one is genuinely beyond repair. Gate Motor & Opener in Burbank has the full breakdown of brands and typical fixes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Burbank
Access control in Burbank means keypads, phone entry, card readers, and video intercoms that have to survive the same thermal cycling that kills operators. On older Burbank properties, the common failure is not the keypad itself but the wiring run through 60-year-old conduit that has cracked and let moisture into the connections. We troubleshoot the system as a whole, not just the device on the post, because a keypad that drops codes intermittently usually has a corroded splice somewhere between the house and the gate. For the full scope of what we service, see Gate Access Control.
Keypad Entry
Signs you need it
Codes work sometimes, the keypad beeps but the gate does not move, or only some codes open the gate.
What it costs in Burbank
Keypad replacement or rewiring in Burbank typically runs $350 to $650 depending on how much of the original conduit can be reused.
How we do it
We pull the keypad, check voltage at the board, isolate the failed wire run, and re-terminate or replace the cable before reprogramming entry codes.
Video Intercom
Signs you need it
The screen freezes, audio cuts out on warm afternoons, or the camera loses signal when the gate moves.
What it costs in Burbank
Video intercom repair or replacement in Burbank typically runs $500 to $950, with camera-only replacements at the lower end.
How we do it
We test the camera, the inside monitor, and the cable path, then replace the failed component and verify two-way audio before we leave.
What Gate Access Control Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Keypad entry repair or replacement | $350 - $650 |
| Video intercom repair or replacement | $500 - $950 |
| Phone entry or card reader system | $450 - $800 |
Can you fix my gate access control the same day in Burbank?
Emergency access-control failures, especially a gate stuck open or a keypad that will not accept any code, are handled same-day throughout Burbank. Call (213) 463-6296 and a live person will confirm a dispatch window.
Does Burbank require a permit for access control upgrades?
Burbank building and safety reviews new automated gate installations under its own permit threshold, and commercial properties along the Alameda Ave corridor are inspected for UL 325 photo-eye compliance. Residential keypad swaps usually do not need a permit, but we will tell you if yours does before any work starts.
Gate Parts & Welding in Burbank
Parts and welding work in Burbank splits into the old-iron problems on 1950s gates and the modern fixes on automated systems. The hinge that worked fine for 60 years fails because the post it was lagged into has cracked, and welding a new hinge onto a shifted post just moves the problem down the frame. We cut out the failed section, weld in new material, and re-secure the post itself when needed. For details on what we carry and what we fabricate, see Gate Parts & Welding.
Hinge Replacement
Signs you need it
The gate sag at the latch side, the lower corner scrapes the driveway, or the hinge pin has visible play when you lift the gate.
What it costs in Burbank
Hinge replacement on a standard Burbank swing gate typically runs $250 to $450 per hinge set, including realigning the gate to the post.
How we do it
We support the gate, cut or unbolt the old hinges, weld or bolt new ones to a plumb post, and photograph the final alignment.
Custom Welding
Signs you need it
The frame has cracked through, a decorative element snapped off, or you need a new section fabricated to match the original ironwork.
What it costs in Burbank
Custom welding and fabrication in Burbank typically runs $200 to $600 per section depending on materials and finish work required.
How we do it
We cut back the damaged steel, weld in a matched replacement section, grind the joints smooth, and leave a photo record of the repair.
What Gate Parts & Welding Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Hinge replacement (per set) | $250 - $450 |
| Custom welding (per section) | $200 - $600 |
| Post replacement | $400 - $800 |
Do you weld on site in Burbank, or do you remove the gate?
Most hinge and frame welding is done on site with the gate supported in place. Removing the gate adds time and cost only when the damage is in an area that requires bench work.
Can you match the original ironwork on a 1950s Burbank gate?
We fabricate replacement sections to match the existing pattern, including the spear tips and scrollwork common on mid-century Burbank gates. The finish is matched after welding so the repair does not stand out.
Brands We Service in Burbank
We service BFT, Linear, Viking, and Ghost Controls operators in Burbank, among others, and stock common parts locally. Most repairs turn around same-day because we do not wait on shipped boards. Our brands page lists the full lineup.
Pricing for Gate Repair in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Keypad entry repair or replacement | $350 - $650 |
| Video intercom repair or replacement | $500 - $950 |
| Phone entry or card reader system | $450 - $800 |
| Hinge replacement (per set) | $250 - $450 |
| Custom welding (per section) | $200 - $600 |
| Post replacement | $400 - $800 |
| Gate motor replacement | $850 - $1,500 |
| Track repair for slide gates | $300 - $700 |
Two things push Burbank prices up: the extra-wide Rancho Equestrian gates that require heavier hardware, and the old concrete posts that have to be re-plumbed before new hinges or operators go on. Every price we give is written down and handed to you before any work starts, under Haven Standard Clause 1.
Neighborhoods We Serve in Burbank
We work throughout Burbank, from the flatlands to the hillside streets. Response time for emergency gate repairs in most of the city is under two hours.
- Magnolia Park
- Rancho Equestrian District
- Hillside District
- Burbank Blvd corridor
- North Burbank
Service Area - Cities Near Burbank
We also cover the adjacent Valley and foothill communities. If you are in North Hollywood, CA, Studio City, CA, Van Nuys, CA, or West Hollywood, CA, call (213) 463-6296 for a written quote on any gate repair.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Burbank
Most Burbank emergency calls, especially during October and November when Santa Ana winds knock gates out of alignment, get a technician on site within two hours. A live person answers at (213) 463-6296 any time of day.
Burbank building and safety has its own permit threshold for automated gate installations, and commercial properties near the studio corridors are inspected for UL 325 photo-eye compliance. We will tell you before any work starts whether your job needs a permit.
Many Burbank HOAs, particularly in the hillside communities, have recorded design standards for gate style and height. We work from your HOA’s requirements and can fabricate to match the approved design rather than forcing a stock gate into a restricted opening.
For any gate repair in Burbank, call Vance Gate Repair at (213) 463-6296 for a free estimate and a written price before work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.