Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Repair for Sherman Oaks Homeowners
A driveway gate that won’t close leaves a Sherman Oaks home open to anyone who walks up. That’s the first problem. The second is the repair itself: some companies send a technician who quotes verbally, fixes the symptom, and leaves no record of what was actually wrong. At Vance Gate Repair, we do it differently. Adrian Vance started this company in 2014 after years of commercial access-control work, where every job required a written scope and a documented trail. We brought that habit to residential gate repair in Sherman Oaks, and today it’s the standard on every visit. You get a written price before any work starts, a photographed record of what we found and fixed, and the 365-Day Done Right Promise backing every repair. Call (213) 463-6296 and a live person answers. Same-day service is available throughout Sherman Oaks, from the hills around Mulholland to the flats near Ventura Boulevard.
What Our Gate Repair Service Includes
Gate repair covers a lot of ground: motors that stopped responding, gates that sag on their hinges, locks that no longer engage, welds that cracked. We diagnose each one the same way: find the cause, name the price in writing, fix it, and leave you with photographic evidence of what changed. Here’s exactly what falls under gate repair at Vance Gate Repair Sherman Oaks.
Electric Gate Repair
Electric gates fail for reasons that aren’t always obvious: a transformer burned out after a power surge, a wire corroded inside the conduit, a receiver stopped talking to the remote. We trace the circuit rather than guessing at it. On every Electric Gate Repair in Sherman Oaks, we test voltage at the board, check continuity on the low-voltage run, and photograph the readings before and after the fix. You’ll see the actual measurements, not just a bill that says “repaired.”
Automatic Gate Repair
An automatic gate that opens a few inches and reverses, or one that starts and stops mid-travel, usually points to a limit-switch problem or a binding hinge. Automatic Gate Repair means setting travel limits correctly, not just moving them slightly and hoping. We reset limits to the manufacturer’s spec, torque the arm brackets to specification, and run the gate through a full open-close cycle while it’s under our watch. The limit positions get photographed and logged so the next service call never starts from zero.
Hinge & Post Repair
Most gate sag in Sherman Oaks comes down to two things: dried-out hinges or a post that’s shifted in the soil. We weld or replace forged hinges rather than shimming worn ones, because shims buy six months and then the gate drops again. Hinge & Post Repair is what we do instead of temporary fixes. If the post itself has moved, we reset it in fresh concrete with proper depth for the gate’s weight and leaf width. On this repair, we photograph the post excavation before it’s backfilled, so you can see what’s holding your gate.
Gate Realignment
A gate that scrapes the driveway or sits an inch low at the latch is a gate that’s working against itself, and every cycle wears the motor harder. We realign the leaves by adjusting hinges, shimming within tolerance, and re-checking the latch engagement. Gate Realignment gets treated as a repair, not a tune-up. After we’re done, both leaves should close square and the latch should drop without slamming or lifting.
Lock Repair
Maglocks, solenoid locks, and mechanical deadbolts all fail in predictable ways: the maglock loses holding force, the solenoid stops retracting, the key cylinder binds. We rebuild or replace the lock with a part rated for your gate’s weight and duty cycle. Vance Gate Repair Sherman Oaks services both stand-alone mechanical locks and the electric locks tied into your opener and intercom. Every lock repair includes a record of the part number installed.
Weld & Rust Repair
Rust on a steel gate isn’t just cosmetic once it reaches the weld seams. We grind back corrosion to clean metal, re-weld the affected joints, and treat the repair area with a rust-inhibiting primer before finishing. On heavier damage, we replace entire sections of square tube rather than stacking weld on top of compromised steel. The repair gets photographed at each stage: before, after grinding, after welding, after finishing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Repair
We work on whatever motor is already on your property. That’s the point. A gate company that only services one brand will steer you toward replacement the moment they see a different nameplate. We service nine major automation brands, and in Sherman Oaks we see a lot of BFT and Linear operators on the hillside properties, and plenty of Ghost Controls on newer residential installs.
We’ve repaired hundreds of BFT control boards in the Los Angeles area, and we stock their commonly replaced components: limit switches, capacitors, and receiver modules. Linear operators show up across Sherman Oaks on swing gates from the 2000s and 2010s; they’re reliable machines, and most of their failures are in the arm assembly or the photo-eyes. Ghost Controls is a newer residential brand with a different control-board architecture, and we’ve worked through their travel-learning procedures enough times to set them correctly on the first visit. Viking and LiftMaster come through the shop regularly as well. Whatever operator is on the gate, we’ll diagnose it and repair it, rather than recommending a replacement you don’t need.
Before
AfterSigns You Need Gate Repair Right Now
- The gate hesitates or reverses mid-travel. This usually means the limit switches are drifting or the safety sensor is misreading. Every reversal cycle strains the motor and the gearbox, so a two-second hesitation today becomes a burned-out motor in a few months.
- The gate scrapes the driveway or sags at the latch. Hinge wear and post movement are progressive. Once the gate starts scraping, it will only get lower, and the latch will eventually stop engaging entirely.
- The motor runs but the gate doesn’t move. A sheared drive key, a stripped gear, or a failed chain link are all common. The motor is working; the mechanical linkage isn’t. Continuing to press the remote burns the motor out faster.
- You hear grinding or squealing when the gate operates. Metal-on-metal noise means a bearing is dry or a gear is eating itself. Lubricating a failing gear quiets it for a week and guarantees a bigger repair later.
- The remote works only from a few feet away. This can be a failing receiver, a damaged antenna wire, or interference from a nearby transmitter. If the range has dropped noticeably, the receiver board is the likely culprit.
If any of these match what your gate is doing, call (213) 463-6296. We’ll talk through the symptom, give you a straight answer about what it likely is, and get a technician out to Sherman Oaks the same day if needed.
Our Gate Repair Process - Step by Step
We don’t arrive with a truck full of parts and a plan to replace things until something works. Every repair follows the same sequence, and you see the documentation at each stage.
- 1
Written diagnosis and written price. The technician finds the cause, explains it in plain language, and writes down the exact price before any tool touches the gate. Under Haven Standard Clause 1, that price is binding. If you don’t approve it, no work happens and the diagnostic is free.
- 2
Photographic evidence of the failure. Before anything is removed or adjusted, we photograph the failed component, the meter reading, the misaligned setting, or the cracked weld. You see what we saw.
- 3
The repair itself. We replace or rebuild the failed part with a component rated for your gate’s weight and duty cycle. No shortcuts, no “this should hold for now.” If we’re replacing a part, you get the manufacturer and part number in writing.
- 4
Verification and photo documentation. The gate runs through full open and close cycles under load. We test all safety sensors, check the force settings, and photograph the final readings and the installed part. This record goes home with you and into your job file.
- 5
The walk-through. The technician walks you through what was wrong, what was done, and what the photos show. You get the written record on the spot. The repair is then covered by the 365-Day Done Right Promise.
How Much Does Gate Repair Cost in Sherman Oaks?
Most gate repairs in Sherman Oaks fall between $175 and $1,400, depending on what failed. A photo-eye realignment or a limit-switch reset is at the low end. Replacing a swing-gate arm assembly usually runs $400 to $800 depending on the brand and whether the bracket is intact. Rebuilding a hinge and post assembly ranges from $600 to $1,400 depending on post condition and gate weight. Control board replacement on a BFT or Linear operator typically falls between $500 and $950.
What affects the price: the brand and age of the operator, whether the failure is electrical or mechanical, and whether any structural steel needs welding. You avoid overpaying by getting the written price before work starts and by seeing photographic evidence that the part actually failed. Our free estimate includes the diagnostic and the written quote. If you already have a written estimate from another company, we’ll review it at no cost and tell you honestly whether it’s fair. You’ll never get a price over the phone, and you’ll never get an invoice that wasn’t agreed to in writing first.
Gate Repair Near Sherman Oaks - Our Service Area
Our technicians cover Sherman Oaks directly, and we service the surrounding neighborhoods throughout the San Fernando Valley and west side. We get to Van Nuys, Encino, Studio City, and North Hollywood quickly, and we regularly run calls in Tarzana, Burbank, Beverly Hills, West Hollywood, and Santa Monica. If you’re in Van Nuys with a gate that won’t close, or in Encino with an opener that died, the same written-price and photo-documentation standard applies. We’re also the Sherman Oaks gate repair team for the hillside neighborhoods above Mulholland. Return to our home page for the full service list.
Serving Sherman Oaks, CA - Our Local Coverage Area
We’re based in the Sherman Oaks area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Repair in Sherman Oaks
Gate repair is the diagnosis and correction of any failure that prevents a driveway or pedestrian gate from opening, closing, latching, or stopping safely. It covers electric motors, control boards, sensors, hinges, posts, locks, and welded steel components. At Vance Gate Repair Sherman Oaks, every repair starts with a written diagnosis and a written price before work begins.
Most repairs are completed in one visit, usually within two to four hours. A limit-switch reset or photo-eye alignment is often a 60-minute job. A full post reset with concrete work can take a full day, and some weld repairs requiring cure time may need a follow-up the next morning. You’ll know the time estimate in writing before we start. Call (213) 463-6296 and we’ll give you a straight answer for your specific symptom.
Gate repair in Sherman Oaks typically costs between $175 and $1,400, with most common repairs landing between $400 and $900. The exact price depends on the failed component, the brand of the operator, and whether structural work is needed. Every quote is delivered in writing before any work starts, and the price you see is the price you pay. Estimates are free.
Yes. We service BFT, Linear, and seven other major automation brands including Viking, Ghost Controls, LiftMaster, FAAC, DoorKing, Elite, and Mighty Mule. We stock commonly replaced parts for BFT and Linear specifically, and our technicians are trained on the travel-learning and limit-setting procedures for each brand. We don’t steer you toward a replacement just because we don’t stock a part.
Yes. A live person answers our phone 24 hours a day, seven days a week, and we dispatch same-day emergency technicians for a gate that won’t close or won’t secure. An open gate is a security problem, and we treat it that way. Call (213) 463-6296 any time; you won’t get a voicemail loop.
Every repair we complete in Sherman Oaks is covered by our 365-Day Done Right Promise. If the repair isn’t right within one full year, we make it right at no additional charge. No argument, no fee, no expiration date within that window. This applies to every part we install and every adjustment we make.
You don’t need to prepare much. If possible, clear any obstructions around the gate’s swing path and make sure we have access to the gate’s power disconnect if there is one. Know where the remote controls are, and if you have a gate intercom or keypad, note any recent behavior changes. The technician handles the rest, and you’ll get a written summary when the job is done.
Schedule Your Gate Repair Service in Sherman Oaks Today
Call (213) 463-6296 for a free, no-obligation estimate on gate repair in Sherman Oaks. A live person answers at any hour. You’ll get a written price before any work starts, a documented photo record when we leave, and a full year of coverage under the 365-Day Done Right Promise. If the gate isn’t working, don’t wait until it’s a security liability. Call now.
Written by Adrian Vance, Owner at Vance Gate Repair, providing written-price gate repair in Sherman Oaks since 2014.